• Material Properties
  • UPVC Pipe Dimensions
  • Pipes For Water Supply
  • Pipes for Soil, Waste, & Vent
  • Pipe for Underground Gravity Drainage & Sewage
  • Electrical & Telecommunication Cable Conduit
  • Electrical & Telecommunication Underground Ducts
  • UPVC Pipe to British Standards for Potable Water
  • Fabricated Drawn Radius Bends
  • Fabricated Couplings
  • Rigid PVC Pipe Dimensions Based on ASTM D1785 & D2665
  • Effect of Elevated Temperature on Rigid PVC Pipe
  • Rigid PVC Conduit
  • Rigid PVC Fabricated Elbows to NEMA TC 3
  • Rigid PVC Fabricated Bends to NEMA TC 9
  • Handling and Storage
  • Introduction
  • FlowGuard™ - The Right Product
  • Material Properties
  • Chemical Properties
  • Hot & Cold Water Systems - Dimensions
  • Effect of Elevated Temperature
  • Advantages of CPVC Pipe
  • Introduction
  • Material Designation
  • Polyethylene Material Properties
  • HDPE Pressure Pipes for Water Supply - Dimensions
  • HDPE Non Pressure Pipes - Dimensions
  • HDPE Sub-Duct with Pre-Installed Pull Rope Inside
  • Sub-Duct & Miniduct - Dimensions
  • Advantages of Polyethylene Pipes
  •  
    Visited By : 1060166 People
     
    UPVC PIPES » Rigid PVC Fabricated Bends to NEMA TC 9
     

    For Cable Ducts & Conduits
    Standard Radius Bends
    For use with:
    Type EB and Type DB
    NEMA TC 6 and 8 
    Rigid PVC Duct.
    Dimensions of 22º, 30º, 45º and 90º

     

     
     
    Table 1.18
    Nominal Size
    of Bend
    (Inches)
    22º, 30º, 45º and 90º
    Radius (R)
    Minimum Straight Tangent
    Length at End (cm)
    Inches
    Meters
    Inches
    Millimeters
    18
    0.46
     
     
    24
    36
    0.61
    0.91
    44.5
     2
    18
    24
    0.46
    0.61
     
     
    36
    48
    0.91
    1.22
    2
    50.8
     3
    18
    24
    0.46
    0.61
     
     
    36
    48
    0.91
    1.22
    3-1/8
    79.4
     4/div>
    18
    24
    0.46
    0.61
     
     
    36
    48
    0.91
    1.22
    3-3/8
    85.7
     5
    18
    24
    0.46
    0.61
     
     
    36
    48
    0.91
    1.22
    3-5/8
    92.1
     6
    18
    24
    0.46
    0.61
     
     
    36
    48
    0.91
    1.22
    95.2
     

    Note:
    Double solvent weld sockets or plain ends are also available.
    Bends in other angles and ridii are available.
     
     
    Note:
    Conduit and Duct of other specifications are available on request. Please contact our Sales and Marketing department.

     
    © Copyright 2012 - 2014 SAPPCO DAMMAM FACTORY. All rights reserved. Designed By : SAUDI SOFTECH
    For detail view of website. You must required internet explorer 8/10 with adobe flash player 10.3 Download IE 10 | Download Flash Player